Dynamixel2Arduino.cpp

/*******************************************************************************
* Copyright 2016 ROBOTIS CO., LTD.
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
*     http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*******************************************************************************/

#include "Dynamixel2Arduino.h"

namespace DYNAMIXEL{

const uint16_t model_number_table[] PROGMEM = {
    AX12A, AX12W, AX18A,
    
    RX10, RX24F, RX28, RX64,
    
    DX113, DX116, DX117,
    
    EX106,

    MX12W,  MX28,   MX64,    MX106,
    MX28_2, MX64_2, MX106_2,
    
    XL320,
    XL330_M288,
    XL330_M077,
    XC330_M181,
    XC330_M288,    
    XC330_T181,
    XC330_T288,    
    XM335_T323,
    XL430_W250,
    XXL430_W250,
    XC430_W150,  XC430_W240,
    XXC430_W250,
    XM430_W210,  XM430_W350,
    XM540_W150,  XM540_W270, 
    XH430_V210,  XH430_V350, XH430_W210, XH430_W350,
    XH540_V150,  XH540_V270, XH540_W150, XH540_W270,
    XD430_T210,  XD430_T350,
    XD540_T150,  XD540_T270,
    XW430_T200,  XW430_T333,
    XW540_T140,  XW540_T260,

    PRO_L42_10_S300_R,   
    PRO_L54_30_S400_R,   PRO_L54_30_S500_R,   PRO_L54_50_S290_R,   PRO_L54_50_S500_R,
    PRO_M42_10_S260_R,   PRO_M42_10_S260_RA,
    PRO_M54_40_S250_R,   PRO_M54_40_S250_RA,  PRO_M54_60_S250_R,   PRO_M54_60_S250_RA,
    PRO_H42_20_S300_R,   PRO_H42_20_S300_RA,
    PRO_H54_100_S500_R,  PRO_H54_100_S500_RA, PRO_H54_200_S500_R,  PRO_H54_200_S500_RA,

    PRO_M42P_010_S260_R, 
    PRO_M54P_040_S250_R, PRO_M54P_060_S250_R,
    PRO_H42P_020_S300_R, 
    PRO_H54P_100_S500_R, PRO_H54P_200_S500_R,

    YM070_210_M001_RH, YM070_210_B001_RH, YM070_210_R051_RH, YM070_210_R099_RH, YM070_210_A051_RH, YM070_210_A099_RH,
    YM080_230_M001_RH, YM080_230_B001_RH, YM080_230_R051_RH, YM080_230_R099_RH, YM080_230_A051_RH, YM080_230_A099_RH
};

const uint8_t model_number_table_count = sizeof(model_number_table)/sizeof(model_number_table[0]);

enum Functions{
  SET_ID,
  SET_BAUD_RATE,

  SET_PROTOCOL,
 
  SET_POSITION,
  GET_POSITION,

  SET_VELOCITY,
  GET_VELOCITY,

  SET_PWM,
  GET_PWM,

  SET_CURRENT,
  GET_CURRENT,

  LAST_DUMMY_FUNC = 0xFF
};

} //namespace DYNAMIXEL

using namespace DYNAMIXEL;

typedef struct ModelDependencyFuncItemAndRangeInfo{
  uint8_t func_idx; //enum Functions
  uint8_t item_idx; //enum ControlTableItem
  uint8_t unit_type; //enum ParamUnit
  int32_t min_value;
  int32_t max_value;
  float unit_value;
} ModelDependencyFuncItemAndRangeInfo_t;

typedef struct ItemAndRangeInfo{
  uint8_t item_idx; //enum ControlTableItem
  uint8_t unit_type; //enum ParamUnit
  int32_t min_value;
  int32_t max_value;
  float unit_value;
} ItemAndRangeInfo_t;

static ItemAndRangeInfo_t getModelDependencyFuncInfo(uint16_t model_num, uint8_t func_num);
static float f_map(float x, float in_min, float in_max, float out_min, float out_max);
static bool checkAndconvertWriteData(float in_data, int32_t &out_data, uint8_t unit, ItemAndRangeInfo_t &item_info);
static bool checkAndconvertReadData(int32_t in_data, float &out_data, uint8_t unit, ItemAndRangeInfo_t &item_info);


Dynamixel2Arduino::Dynamixel2Arduino(uint16_t packet_buf_size)
: Master(2.0, packet_buf_size), model_number_idx_last_index_(0)
{
  memset(&model_number_idx_, 0xff, sizeof(model_number_idx_));
}

Dynamixel2Arduino::Dynamixel2Arduino(HardwareSerial& port, int dir_pin, uint16_t packet_buf_size)
: Master(2.0, packet_buf_size), model_number_idx_last_index_(0)
{
  p_dxl_port_ = new SerialPortHandler(port, dir_pin);
  setPort(p_dxl_port_);
  memset(&model_number_idx_, 0xff, sizeof(model_number_idx_));
}

/* For Master configuration */
void Dynamixel2Arduino::begin(unsigned long baud)
{
  p_dxl_port_ = (SerialPortHandler*)getPort();

  if(p_dxl_port_ == nullptr){
    setLastLibErrCode(D2A_LIB_ERROR_NULLPTR_PORT_HANDLER);
    return;
  }

  p_dxl_port_->begin(baud);
}

unsigned long Dynamixel2Arduino::getPortBaud()
{
  p_dxl_port_ = (SerialPortHandler*)getPort();

  if(p_dxl_port_ == nullptr){
    setLastLibErrCode(D2A_LIB_ERROR_NULLPTR_PORT_HANDLER);
    return 0;
  }

  return p_dxl_port_->getBaud();
}

bool Dynamixel2Arduino::scan()
{
  bool ret = true;

  ret = ping();

  return ret;
}

bool Dynamixel2Arduino::ping(uint8_t id)
{
  bool ret = false;
 
  if (id != DXL_BROADCAST_ID){
    InfoFromPing_t recv_info;
    if(Master::ping(id, &recv_info, 1, 10) > 0){
      if(recv_info.id == id){
        if(getPortProtocolVersion() == 1.0){
          recv_info.model_number = getModelNumber(id);
        }
        ret = setModelNumber(id, recv_info.model_number);
      }
    }
  }else{
    uint8_t recv_ids[254];
    uint8_t recv_cnt;

    recv_cnt = Master::ping(DXL_BROADCAST_ID, recv_ids, sizeof(recv_ids), 3*253);

    if(recv_cnt > 0){
      for (uint8_t i=0; i<recv_cnt; i++){
        (void)setModelNumber(recv_ids[i], getModelNumber(id));
      }
      ret = true;
    }
  }

  return ret;  
}

bool 
Dynamixel2Arduino::setModelNumber(uint8_t id, uint16_t model_number)
{
  bool ret = false;

  if(id <= 253){
    model_number_idx_[id] = getModelNumberIndex(model_number);
    ret = (model_number_idx_[id] != 0xFF) ? true:false;
    if(ret == false){
      setLastLibErrCode(D2A_LIB_ERROR_UNKNOWN_MODEL_NUMBER);
    }
  }else{
    setLastLibErrCode(DXL_LIB_ERROR_INVAILD_ID);
  }

  return ret;
}

uint16_t Dynamixel2Arduino::getModelNumber(uint8_t id)
{
  uint16_t model_num = 0xFFFF;

  (void) read(id, COMMON_MODEL_NUMBER_ADDR, COMMON_MODEL_NUMBER_ADDR_LENGTH,
   (uint8_t*)&model_num, sizeof(model_num), 20);

  return model_num;
}

bool Dynamixel2Arduino::setID(uint8_t id, uint8_t new_id)
{
  return writeControlTableItem(ControlTableItem::ID, id, new_id);
}

bool Dynamixel2Arduino::setProtocol(uint8_t id, float version)
{
  uint8_t ver_idx;

  if(version == 1.0){
    ver_idx = 1;
  }else if(version == 2.0){
    ver_idx = 2;
  }else{
    setLastLibErrCode(DXL_LIB_ERROR_INVAILD_PROTOCOL_VERSION);
    return false;
  }

  return writeControlTableItem(ControlTableItem::PROTOCOL_VERSION, id, ver_idx);
}

//TODO: Simplify the code by grouping model numbers.
bool Dynamixel2Arduino::setBaudrate(uint8_t id, uint32_t baudrate)
{
  uint16_t model_num = getModelNumberFromTable(id);
  uint8_t baud_idx = 0;

  switch(model_num)
  {
    case AX12A:
    case AX12W:
    case AX18A:
    case DX113:
    case DX116:
    case DX117:
    case RX10:
    case RX24F:
    case RX28:
    case RX64:
    case EX106:    
    case MX12W:
    case MX28:
    case MX64:
    case MX106:
      // baud_idx = round(2000000.0/(float)baudrate) - 1;
      // if(baud_idx > 254)
      //   return false;
      switch(baudrate)
      {
        case 9600:
          baud_idx = 207;
          break;
        case 57600:
          baud_idx = 34;
          break;
        case 115200:
          baud_idx = 16;
          break;
        case 1000000:
          baud_idx = 1;
          break;
        default:
          return false;                    
      }        
      break;

    case XL320:
      switch(baudrate)
      {
        case 9600:
          baud_idx = 0;
          break;
        case 57600:
          baud_idx = 1;
          break;
        case 115200:
          baud_idx = 2;
          break;
        case 1000000:
          baud_idx = 3;
          break;
        default:
          return false;                    
      }    
      break;
    case XM335_T323:
    case XC330_M288:
    case XC330_M181:
    case XC330_T288:
    case XC330_T181:
    case XL330_M288:
    case XL330_M077:
      switch(baudrate)
      {
        case 9600:
          baud_idx = 0;
          break;
        case 57600:
          baud_idx = 1;
          break;
        case 115200:
          baud_idx = 2;
          break;
        case 1000000:
          baud_idx = 3;
          break;
        case 2000000:
          baud_idx = 4;
          break;
        case 3000000:
          baud_idx = 5;
          break;
        case 4000000:
          baud_idx = 6;
          break;
        default:
          return false;                    
      }    
      break;

    case MX28_2:
    case MX64_2:
    case MX106_2:
    case XC430_W150:
    case XC430_W240:
    case XXC430_W250:
    case XL430_W250:
    case XXL430_W250:
    case XM430_W210:
    case XM430_W350:
    case XH430_V210:
    case XH430_V350:
    case XH430_W210:
    case XH430_W350:
    case XD430_T210:
    case XD430_T350:
    case XM540_W150:
    case XM540_W270:
    case XH540_W150:
    case XH540_W270:
    case XH540_V150:
    case XH540_V270:
    case XD540_T150:
    case XD540_T270:
    case XW430_T200:
    case XW430_T333:
    case XW540_T140:
    case XW540_T260:    
      switch(baudrate)
      {
        case 9600:
          baud_idx = 0;
          break;
        case 57600:
          baud_idx = 1;
          break;
        case 115200:
          baud_idx = 2;
          break;
        case 1000000:
          baud_idx = 3;
          break;
        case 2000000:
          baud_idx = 4;
          break;
        case 3000000:
          baud_idx = 5;
          break;
        case 4000000:
          baud_idx = 6;
          break;
        case 4500000:
          baud_idx = 7;
          break;    
        default:
          return false;          
      }
      break;

    // case PRO_L42_10_S300_R:
    // case PRO_L54_30_S400_R:
    // case PRO_L54_30_S500_R:
    // case PRO_L54_50_S290_R:
    // case PRO_L54_50_S500_R:
    case PRO_M42_10_S260_R:
    case PRO_M54_40_S250_R:
    case PRO_M54_60_S250_R:
    case PRO_H42_20_S300_R:
    case PRO_H54_100_S500_R:
    case PRO_H54_200_S500_R:
      switch(baudrate)
      {
        case 9600:
          baud_idx = 0;
          break;
        case 57600:
          baud_idx = 1;
          break;
        case 115200:
          baud_idx = 2;
          break;
        case 1000000:
          baud_idx = 3;
          break;
        case 2000000:
          baud_idx = 4;
          break;
        case 3000000:
          baud_idx = 5;
          break;
        case 4000000:
          baud_idx = 6;
          break;
        case 4500000:
          baud_idx = 7;
          break;
        case 10500000:
          baud_idx = 8;
          break;
        default:
          return false;          
      }
      break;

    case PRO_M42_10_S260_RA:
    case PRO_M54_40_S250_RA:
    case PRO_M54_60_S250_RA:
    case PRO_H42_20_S300_RA:
    case PRO_H54_100_S500_RA:
    case PRO_H54_200_S500_RA:
    case PRO_H42P_020_S300_R:
    case PRO_H54P_100_S500_R:
    case PRO_H54P_200_S500_R:
    case PRO_M42P_010_S260_R:
    case PRO_M54P_040_S250_R:
    case PRO_M54P_060_S250_R:
      switch(baudrate)
      {
        case 9600:
          baud_idx = 0;
          break;
        case 57600:
          baud_idx = 1;
          break;
        case 115200:
          baud_idx = 2;
          break;
        case 1000000:
          baud_idx = 3;
          break;
        case 2000000:
          baud_idx = 4;
          break;
        case 3000000:
          baud_idx = 5;
          break;
        case 4000000:
          baud_idx = 6;
          break;
        case 4500000:
          baud_idx = 7;
          break;
        case 6000000:
          baud_idx = 8;
          break;          
        case 10500000:
          baud_idx = 9;
          break;          
        default:
          return false;          
      }                
      break;

    case YM070_210_M001_RH:
    case YM070_210_B001_RH:
    case YM070_210_R051_RH:
    case YM070_210_R099_RH:
    case YM070_210_A051_RH:
    case YM070_210_A099_RH:
    case YM080_230_M001_RH:
    case YM080_230_B001_RH:
    case YM080_230_R051_RH:
    case YM080_230_R099_RH:
    case YM080_230_A051_RH:
    case YM080_230_A099_RH:
      switch(baudrate)
      {
        case 9600:
          baud_idx = 0;
          break;
        case 57600:
          baud_idx = 1;
          break;
        case 115200:
          baud_idx = 2;
          break;
        case 1000000:
          baud_idx = 3;
          break;
        case 2000000:
          baud_idx = 4;
          break;
        case 3000000:
          baud_idx = 5;
          break;
        case 4000000:
          baud_idx = 6;
          break;
        case 4500000:
          baud_idx = 7;
          break;
        case 6000000:
          baud_idx = 8;
          break;          
        case 10500000:
          baud_idx = 9;
          break;          
        default:
          return false;          
      }                
      break;

    default:
      return false;
      break;
  }

  return writeControlTableItem(ControlTableItem::BAUD_RATE, id, baud_idx);
}


/* Commands for Slave */
bool Dynamixel2Arduino::torqueOn(uint8_t id)
{
  return setTorqueEnable(id, true);
}

bool Dynamixel2Arduino::torqueOff(uint8_t id)
{
  return setTorqueEnable(id, false);
}

bool Dynamixel2Arduino::setTorqueEnable(uint8_t id, bool enable)
{
  return writeControlTableItem(ControlTableItem::TORQUE_ENABLE, id, enable);
}

bool Dynamixel2Arduino::ledOn(uint8_t id)
{
  return setLedState(id, true);
}

bool Dynamixel2Arduino::ledOff(uint8_t id)
{
  return setLedState(id, false);
}

bool Dynamixel2Arduino::setLedState(uint8_t id, bool state)
{
  bool ret = false;
  uint16_t model_num = getModelNumberFromTable(id);

  switch(model_num)
  {
    // case PRO_L42_10_S300_R:
    // case PRO_L54_30_S400_R:
    // case PRO_L54_30_S500_R:
    // case PRO_L54_50_S290_R:
    // case PRO_L54_50_S500_R:
    case PRO_M42_10_S260_R:
    case PRO_M54_40_S250_R:
    case PRO_M54_60_S250_R:
    case PRO_H42_20_S300_R:
    case PRO_H54_100_S500_R:
    case PRO_H54_200_S500_R:
    case PRO_M42_10_S260_RA:
    case PRO_M54_40_S250_RA:
    case PRO_M54_60_S250_RA:
    case PRO_H42_20_S300_RA:
    case PRO_H54_100_S500_RA:
    case PRO_H54_200_S500_RA:
    case PRO_H42P_020_S300_R:
    case PRO_H54P_100_S500_R:
    case PRO_H54P_200_S500_R:
    case PRO_M42P_010_S260_R:
    case PRO_M54P_040_S250_R:
    case PRO_M54P_060_S250_R:
          if (state == false) {
              writeControlTableItem(ControlTableItem::DXL_LED_GREEN, id, state);
              writeControlTableItem(ControlTableItem::DXL_LED_BLUE, id, state);
          }
      ret = writeControlTableItem(ControlTableItem::DXL_LED_RED, id, state);
      break;

    default:
      ret = writeControlTableItem(ControlTableItem::DXL_LED, id, state);
      break;
  }

  return ret;
}


//TODO: Simplify the code by grouping model numbers.
bool Dynamixel2Arduino::setOperatingMode(uint8_t id, uint8_t mode)
{
  bool ret = false;
  uint16_t model_num = getModelNumberFromTable(id);

  switch(model_num)
  {
    case AX12A:
    case AX12W:
    case AX18A:
    case DX113:
    case DX116:
    case DX117:
    case RX10:
    case RX24F:
    case RX28:
    case RX64:
      if(mode == OP_POSITION){
        if(writeControlTableItem(ControlTableItem::CW_ANGLE_LIMIT, id, 0))
          ret = writeControlTableItem(ControlTableItem::CCW_ANGLE_LIMIT, id, 1023);
      }else if(mode == OP_VELOCITY){
        if(writeControlTableItem(ControlTableItem::CW_ANGLE_LIMIT, id, 0))
          ret = writeControlTableItem(ControlTableItem::CCW_ANGLE_LIMIT, id, 0);
      }
      break;

    case EX106:
      if(mode == OP_POSITION){
        if(writeControlTableItem(ControlTableItem::CW_ANGLE_LIMIT, id, 0))
          ret = writeControlTableItem(ControlTableItem::CCW_ANGLE_LIMIT, id, 4095);
      }else if(mode == OP_VELOCITY){
        if(writeControlTableItem(ControlTableItem::CW_ANGLE_LIMIT, id, 0))
          ret = writeControlTableItem(ControlTableItem::CCW_ANGLE_LIMIT, id, 0);
      }
      break;

    case XL320:
      if(mode == OP_POSITION){
        ret = writeControlTableItem(ControlTableItem::CONTROL_MODE, id, 2);
      }else if(mode == OP_VELOCITY){
        ret = writeControlTableItem(ControlTableItem::CONTROL_MODE, id, 1);
      }
      break;
    
    case MX12W:
    case MX28:
      if(mode == OP_POSITION){
        if(writeControlTableItem(ControlTableItem::CW_ANGLE_LIMIT, id, 0))
          ret = writeControlTableItem(ControlTableItem::CCW_ANGLE_LIMIT, id, 4095);
      }else if(mode == OP_VELOCITY){
        if(writeControlTableItem(ControlTableItem::CW_ANGLE_LIMIT, id, 0))
          ret = writeControlTableItem(ControlTableItem::CCW_ANGLE_LIMIT, id, 0);
      }else if(mode == OP_EXTENDED_POSITION){
        if(writeControlTableItem(ControlTableItem::CW_ANGLE_LIMIT, id, 4095))
          ret = writeControlTableItem(ControlTableItem::CCW_ANGLE_LIMIT, id, 4095);
      }
      break;   

    case MX64:
    case MX106:
      if(mode == OP_POSITION){
        if(writeControlTableItem(ControlTableItem::TORQUE_CTRL_MODE_ENABLE, id, 0)
          || writeControlTableItem(ControlTableItem::CW_ANGLE_LIMIT, id, 0))
          ret = writeControlTableItem(ControlTableItem::CCW_ANGLE_LIMIT, id, 4095);
      }else if(mode == OP_VELOCITY){
        if(writeControlTableItem(ControlTableItem::TORQUE_CTRL_MODE_ENABLE, id, 0)
          || writeControlTableItem(ControlTableItem::CW_ANGLE_LIMIT, id, 0))
          ret = writeControlTableItem(ControlTableItem::CCW_ANGLE_LIMIT, id, 0);
      }else if(mode == OP_EXTENDED_POSITION){
        if(writeControlTableItem(ControlTableItem::TORQUE_CTRL_MODE_ENABLE, id, 0)
          || writeControlTableItem(ControlTableItem::CW_ANGLE_LIMIT, id, 4095))
          ret = writeControlTableItem(ControlTableItem::CCW_ANGLE_LIMIT, id, 4095);
      }else if(mode == OP_CURRENT){
        ret = writeControlTableItem(ControlTableItem::TORQUE_CTRL_MODE_ENABLE, id, 1);
      }
      break;

    case MX28_2:
    case XC430_W150:
    case XC430_W240:
    case XXC430_W250:
    case XL430_W250:
    case XXL430_W250:
      if(mode == OP_POSITION){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 3);
      }else if(mode == OP_VELOCITY){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 1);
      }else if(mode == OP_EXTENDED_POSITION){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 4);
      }else if(mode == OP_PWM){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 16);
      }
      break;

    case MX64_2:
    case MX106_2:
    case XL330_M288:
    case XL330_M077:
    case XC330_M288:
    case XC330_M181:    
    case XC330_T181:
    case XC330_T288:
    case XM335_T323:    
    case XM430_W210:
    case XM430_W350:
    case XH430_V210:
    case XH430_V350:
    case XH430_W210:
    case XH430_W350:
    case XD430_T210:
    case XD430_T350:
    case XM540_W150:
    case XM540_W270:
    case XH540_W150:
    case XH540_W270:
    case XH540_V150:
    case XH540_V270:
    case XD540_T150:
    case XD540_T270:
    case XW430_T200:
    case XW430_T333:
    case XW540_T140:
    case XW540_T260:    
      if(mode == OP_POSITION){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 3);
      }else if(mode == OP_VELOCITY){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 1);
      }else if(mode == OP_EXTENDED_POSITION){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 4);
      }else if(mode == OP_CURRENT){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 0);
      }else if(mode == OP_PWM){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 16);
      }else if(mode == OP_CURRENT_BASED_POSITION){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 5);
      }
      break;            

    // case PRO_L42_10_S300_R:
    // case PRO_L54_30_S400_R:
    // case PRO_L54_30_S500_R:
    // case PRO_L54_50_S290_R:
    // case PRO_L54_50_S500_R:
    case PRO_M42_10_S260_R:
    case PRO_M54_40_S250_R:
    case PRO_M54_60_S250_R:
    case PRO_H42_20_S300_R:
    case PRO_H54_100_S500_R:
    case PRO_H54_200_S500_R:
      if(mode == OP_POSITION){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 3);
      }else if(mode == OP_VELOCITY){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 1);
      }else if(mode == OP_EXTENDED_POSITION){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 4);
      }else if(mode == OP_CURRENT){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 0);
      }
      break;

    case PRO_M42_10_S260_RA:
    case PRO_M54_40_S250_RA:
    case PRO_M54_60_S250_RA:
    case PRO_H42_20_S300_RA:
    case PRO_H54_100_S500_RA:
    case PRO_H54_200_S500_RA:
    case PRO_H42P_020_S300_R:
    case PRO_H54P_100_S500_R:
    case PRO_H54P_200_S500_R:
    case PRO_M42P_010_S260_R:
    case PRO_M54P_040_S250_R:
    case PRO_M54P_060_S250_R:
      if(mode == OP_POSITION){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 3);
      }else if(mode == OP_VELOCITY){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 1);
      }else if(mode == OP_EXTENDED_POSITION){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 4);
      }else if(mode == OP_CURRENT){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 0);
      }else if(mode == OP_PWM){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 16);
      }
      break;

    case YM070_210_M001_RH:
    case YM070_210_B001_RH:
    case YM070_210_R051_RH:
    case YM070_210_R099_RH:
    case YM070_210_A051_RH:
    case YM070_210_A099_RH:
    case YM080_230_M001_RH:
    case YM080_230_B001_RH:
    case YM080_230_R051_RH:
    case YM080_230_R099_RH:
    case YM080_230_A051_RH:
    case YM080_230_A099_RH:
      if(mode == OP_POSITION){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 3);
      }else if(mode == OP_VELOCITY){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 1);
      }else if(mode == OP_CURRENT){
        ret = writeControlTableItem(ControlTableItem::OPERATING_MODE, id, 0);
      }
      break;

    default:
      break;
  }

  return ret;
}

bool Dynamixel2Arduino::setGoalPosition(uint8_t id, float value, uint8_t unit)
{
  if(unit != UNIT_RAW && unit != UNIT_DEGREE)
    return false;

  return writeForRangeDependencyFunc(SET_POSITION, id, value, unit);
}

float Dynamixel2Arduino::getPresentPosition(uint8_t id, uint8_t unit)
{
  if(unit != UNIT_RAW && unit != UNIT_DEGREE)
    return 0.0;

  return readForRangeDependencyFunc(GET_POSITION, id, unit);
}

bool Dynamixel2Arduino::setGoalVelocity(uint8_t id, float value, uint8_t unit)
{
  if(unit != UNIT_RAW && unit != UNIT_PERCENT && unit != UNIT_RPM)
    return false;

  return writeForRangeDependencyFunc(SET_VELOCITY, id, value, unit);
}

float Dynamixel2Arduino::getPresentVelocity(uint8_t id, uint8_t unit)
{
  if(unit != UNIT_RAW && unit != UNIT_PERCENT && unit != UNIT_RPM)
    return 0.0;

  return readForRangeDependencyFunc(GET_VELOCITY, id, unit);
}

bool Dynamixel2Arduino::setGoalPWM(uint8_t id, float value, uint8_t unit)
{
  if(unit != UNIT_RAW && unit != UNIT_PERCENT)
    return false;

  return writeForRangeDependencyFunc(SET_PWM, id, value, unit);
}

float Dynamixel2Arduino::getPresentPWM(uint8_t id, uint8_t unit)
{
  if(unit != UNIT_RAW && unit != UNIT_PERCENT)
    return 0.0;

  return readForRangeDependencyFunc(GET_PWM, id, unit);
}

bool Dynamixel2Arduino::setGoalCurrent(uint8_t id, float value, uint8_t unit)
{
  if(unit != UNIT_RAW && unit != UNIT_PERCENT && unit != UNIT_MILLI_AMPERE)
    return false;

  return writeForRangeDependencyFunc(SET_CURRENT, id, value, unit);
}

float Dynamixel2Arduino::getPresentCurrent(uint8_t id, uint8_t unit)
{
  if(unit != UNIT_RAW && unit != UNIT_PERCENT && unit != UNIT_MILLI_AMPERE)
    return 0.0;

  return readForRangeDependencyFunc(GET_CURRENT, id, unit);
}

bool Dynamixel2Arduino::getTorqueEnableStat(uint8_t id)
{
  bool ret = false;

  if(readControlTableItem(ControlTableItem::TORQUE_ENABLE, id) == DXL_TORQUE_ON){
    ret = true;
  }else{
    ret = false;
  }

  return ret;
}

int32_t Dynamixel2Arduino::readControlTableItem(uint8_t item_idx, uint8_t id, uint32_t timeout)
{
  int32_t ret = 0;
  uint16_t model_num = getModelNumberFromTable(id);

  // To use the command function without ping() or model addition.
  if(model_num == UNREGISTERED_MODEL){
    if(setModelNumber(id, getModelNumber(id)) == true){
      model_num = getModelNumberFromTable(id);
    }
  }

  if(model_num != UNREGISTERED_MODEL){
    ret = readControlTableItem(model_num, item_idx, id, timeout);
  }else{
    setLastLibErrCode(D2A_LIB_ERROR_UNKNOWN_MODEL_NUMBER);
  }

  return ret;
}

bool Dynamixel2Arduino::writeControlTableItem(uint8_t item_idx, uint8_t id, int32_t data, uint32_t timeout)
{
  bool ret = false;
  uint16_t model_num = getModelNumberFromTable(id);
  
  // To use the command function without ping() or model addition.
  if(model_num == UNREGISTERED_MODEL){
    if(setModelNumber(id, getModelNumber(id)) == true){
      model_num = getModelNumberFromTable(id);
    }
  }

  if(model_num != UNREGISTERED_MODEL){
    ret = writeControlTableItem(model_num, item_idx, id, data, timeout);
  }else{
    setLastLibErrCode(D2A_LIB_ERROR_UNKNOWN_MODEL_NUMBER);
  }

  return ret;
}




/* Private Member Function */

int32_t Dynamixel2Arduino::readControlTableItem(uint16_t model_num, uint8_t item_idx, uint8_t id, uint32_t timeout)
{
  int32_t recv_len, ret = 0;
  ControlTableItemInfo_t item_info;

  p_dxl_port_ = (SerialPortHandler*)getPort();
  if(p_dxl_port_ == nullptr){
    setLastLibErrCode(D2A_LIB_ERROR_NULLPTR_PORT_HANDLER);
    return 0;
  }

  item_info = getControlTableItemInfo(model_num, item_idx);

  if(item_info.addr_length > 0)
  {
    recv_len = read(id, item_info.addr, item_info.addr_length, (uint8_t*)&ret, sizeof(ret), timeout);

    if(recv_len == 1){
      int8_t t_data = (int8_t)ret;
      ret = (int32_t)t_data;
    }else if(recv_len == 2){
      int16_t t_data = (int16_t)ret;
      ret = (int32_t)t_data;
    }
  }

  return ret;
}

bool Dynamixel2Arduino::writeControlTableItem(uint16_t model_num, uint8_t item_idx, uint8_t id, int32_t data, uint32_t timeout)
{
  bool ret = false;
  ControlTableItemInfo_t item_info;
  
  p_dxl_port_ = (SerialPortHandler*)getPort();
  if(p_dxl_port_ == nullptr){
    setLastLibErrCode(D2A_LIB_ERROR_NULLPTR_PORT_HANDLER);
    return false;
  }

  item_info = getControlTableItemInfo(model_num, item_idx);
  if(item_info.addr_length > 0){
    ret = write(id, item_info.addr, (uint8_t*)&data, item_info.addr_length, timeout);
  }

  return ret;
}

uint8_t
Dynamixel2Arduino::getModelNumberIndex(uint16_t model_num)
{
  uint8_t i, ret = 0xFF;

  // quick shortcut
  if(model_num == model_number_idx_[model_number_idx_last_index_]){
    ret = model_number_idx_last_index_;
  }else{
    for(i=0; i<model_number_table_count; i++)
    {
      if(model_num == pgm_read_word(&model_number_table[i])){
        model_number_idx_last_index_ = i;
        ret = i;
        break;
      }
    }
  }

  return ret;
}


uint16_t Dynamixel2Arduino::getModelNumberFromTable(uint8_t id)
{
  uint8_t idx;
  uint16_t model_num;

  if(id > 254){
    setLastLibErrCode(DXL_LIB_ERROR_INVAILD_ID);
    return UNREGISTERED_MODEL;
  }

  idx = model_number_idx_[id];
  model_num = (idx < model_number_table_count) ? pgm_read_word(&model_number_table[idx]) : UNREGISTERED_MODEL;

  return model_num;
}

float Dynamixel2Arduino::readForRangeDependencyFunc(uint8_t func_idx, uint8_t id, uint8_t unit)
{
  float ret = 0;
  int32_t recv_data = 0;
  uint16_t model_num = getModelNumberFromTable(id);
  ItemAndRangeInfo_t item_info;

  // To use the command function without ping() or model addition.
  if(model_num == UNREGISTERED_MODEL){
    if(setModelNumber(id, getModelNumber(id)) == true){
      model_num = getModelNumberFromTable(id);
    }
  }

  if(model_num != UNREGISTERED_MODEL){
    item_info = getModelDependencyFuncInfo(model_num, func_idx);

    if(item_info.item_idx != ControlTableItem::LAST_DUMMY_ITEM){
      recv_data = readControlTableItem(model_num, item_info.item_idx, id);
      checkAndconvertReadData(recv_data, ret, unit, item_info);
    }else{
      setLastLibErrCode(D2A_LIB_ERROR_NOT_SUPPORT_FUNCTION);
    }    
  }else{
    setLastLibErrCode(D2A_LIB_ERROR_UNKNOWN_MODEL_NUMBER);
  }

  return ret;
}

bool Dynamixel2Arduino::writeForRangeDependencyFunc(uint8_t func_idx, uint8_t id, float value, uint8_t unit)
{
  bool ret = false;
  int32_t data = 0;
  uint16_t model_num = getModelNumberFromTable(id);
  ItemAndRangeInfo_t item_info;

  // To use the command function without ping() or model addition.
  if(model_num == UNREGISTERED_MODEL){
    if(setModelNumber(id, getModelNumber(id)) == true){
      model_num = getModelNumberFromTable(id);
    }
  }

  if(model_num != UNREGISTERED_MODEL){
    item_info = getModelDependencyFuncInfo(model_num, func_idx);

    if(item_info.item_idx == ControlTableItem::LAST_DUMMY_ITEM)
      return false;

    if(checkAndconvertWriteData(value, data, unit, item_info) == false)
      return false;

    ret = writeControlTableItem(model_num, item_info.item_idx, id, data);
  }else{
    setLastLibErrCode(D2A_LIB_ERROR_UNKNOWN_MODEL_NUMBER);
  }

  return ret;
}





/* Const structure & Static Function */
using namespace ControlTableItem;

/* AX series, XL320 (DX,RX,EX) */
const ModelDependencyFuncItemAndRangeInfo_t dependency_ctable_1_0_common[] PROGMEM = {
#if (ENABLE_ACTUATOR_AX \
 || ENABLE_ACTUATOR_DX \
 || ENABLE_ACTUATOR_RX \
 || ENABLE_ACTUATOR_EX)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, 0, 1023, 0.29},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, 0, 1023, 0.29},

  {SET_VELOCITY, MOVING_SPEED, UNIT_PERCENT, 0, 2047, 0.1},
  {GET_VELOCITY, PRESENT_SPEED, UNIT_PERCENT, 0, 2047, 0.1},  
#endif 
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_ex[] PROGMEM = {
#if (ENABLE_ACTUATOR_EX)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, 0, 4095, 0.06},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, 0, 4095, 0.06},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

/* MX(1.0) series */
const ModelDependencyFuncItemAndRangeInfo_t dependency_ctable_1_1_common[] PROGMEM = {
#if (ENABLE_ACTUATOR_MX12W \
 || ENABLE_ACTUATOR_MX28 \
 || ENABLE_ACTUATOR_MX64 \
 || ENABLE_ACTUATOR_MX106)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -28672, 28672, 0.088},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -28672, 28672, 0.088},

  {SET_VELOCITY, MOVING_SPEED, UNIT_RPM, 0, 2047, 0.114},
  {GET_VELOCITY, PRESENT_SPEED, UNIT_RPM, 0, 2047, 0.114},  
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_mx12[] PROGMEM = {
#if (ENABLE_ACTUATOR_MX12W)
  {SET_VELOCITY, MOVING_SPEED, UNIT_RPM, 0, 2047, 0.916},
  {GET_VELOCITY, PRESENT_SPEED, UNIT_RPM, 0, 2047, 0.916},  
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_mx64_mx106[] PROGMEM = {
#if (ENABLE_ACTUATOR_MX64 \
 || ENABLE_ACTUATOR_MX106)
  {SET_CURRENT, GOAL_TORQUE, UNIT_MILLI_AMPERE, 0, 2047, 4.5},
  {GET_CURRENT, CURRENT, UNIT_MILLI_AMPERE, 0, 4095, 4.5},  
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_xl320[] PROGMEM = {
#if (ENABLE_ACTUATOR_XL320)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, 0, 1023, 0.29},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, 0, 1023, 0.29},

  {SET_VELOCITY, MOVING_SPEED, UNIT_PERCENT, 0, 2047, 0.1},
  {GET_VELOCITY, PRESENT_SPEED, UNIT_PERCENT, 0, 2047, 0.1},  
#endif 
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

/* MX2.0, X series(without XL320) */
const ModelDependencyFuncItemAndRangeInfo_t dependency_ctable_2_0_common[] PROGMEM = {
#if (ENABLE_ACTUATOR_MX28_PROTOCOL2 \
  || ENABLE_ACTUATOR_MX64_PROTOCOL2 \
  || ENABLE_ACTUATOR_MX106_PROTOCOL2 \
  || ENABLE_ACTUATOR_XL330 \
  || ENABLE_ACTUATOR_XC330 \
  || ENABLE_ACTUATOR_XM335 \
  || ENABLE_ACTUATOR_XC430 \
  || ENABLE_ACTUATOR_XL430 \
  || ENABLE_ACTUATOR_XM430 || ENABLE_ACTUATOR_XH430 || ENABLE_ACTUATOR_XD430 \
  || ENABLE_ACTUATOR_XM540 || ENABLE_ACTUATOR_XH540 || ENABLE_ACTUATOR_XD540 \
  || ENABLE_ACTUATOR_XW540 || ENABLE_ACTUATOR_XW430)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -1048575, 1048575, 0.088},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483647 , 2147483647, 0.088},

  {SET_PWM, GOAL_PWM, UNIT_RAW, -885, 885, 1},
  {GET_PWM, PRESENT_PWM, UNIT_RAW, -885, 885, 1},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_mx64_2[] PROGMEM = {
#if (ENABLE_ACTUATOR_MX64_PROTOCOL2)
  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -1193, 1193, 3.36},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -1193, 1193, 3.36},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_mx106_2[] PROGMEM = {
#if (ENABLE_ACTUATOR_MX106_PROTOCOL2)
  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -2047, 2047, 3.36},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -2047, 2047, 3.36},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_xl330_M288_M077[] PROGMEM = {
#if (ENABLE_ACTUATOR_XL330)
  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -1750, 1750, 1},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -1750, 1750, 1},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -2047, 2047, 0.229},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -2047, 2047, 0.229},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_xl430_xc430[] PROGMEM = {
#if (ENABLE_ACTUATOR_MX28_PROTOCOL2 || ENABLE_ACTUATOR_XL430 || ENABLE_ACTUATOR_XC430)
  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_xc330_m181_m288[] PROGMEM = {
#if (ENABLE_ACTUATOR_XC330)
  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -2352, 2352, 1},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -2352, 2352, 1},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -2047, 2047, 0.229},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -2047, 2047, 0.229},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_xc330_t181_t288[] PROGMEM = {
#if (ENABLE_ACTUATOR_XC330)
  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -910, 910, 1},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -910, 910, 1},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -2047, 2047, 0.229},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -2047, 2047, 0.229},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_xm335_t323[] PROGMEM = {
  #if (ENABLE_ACTUATOR_XM335)
    {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -910, 910, 1},
    {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -910, 910, 1},
  
    {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -2047, 2047, 0.229},
    {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -2047, 2047, 0.229},
  #endif
    {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
  };

const ModelDependencyFuncItemAndRangeInfo_t dependency_xm430_w210_w350[] PROGMEM = {
#if (ENABLE_ACTUATOR_XM430)
  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -1193, 1193, 2.69},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -1193, 1193, 2.69},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_xh430_wt210_wt350[] PROGMEM = {
#if (ENABLE_ACTUATOR_XH430 || ENABLE_ACTUATOR_XD430)
  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -648, 648, 2.69},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -648, 648, 2.69},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_xw430_t200_t333[] PROGMEM = {
#if (ENABLE_ACTUATOR_XW430)
  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -2047, 2047, 2.69},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -2047, 2047, 2.69},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_xh430_v210_v350[] PROGMEM = {
#if (ENABLE_ACTUATOR_XH430)
  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -689, 689, 1.34},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -689, 689, 1.34},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_xm540_xh540_xt540_xw540[] PROGMEM = {
#if (ENABLE_ACTUATOR_XM540 || ENABLE_ACTUATOR_XH540 \
 || ENABLE_ACTUATOR_XD540 || ENABLE_ACTUATOR_XW540)
  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -2047, 2047, 2.69},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -2047, 2047, 2.69},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_xh540_v150_v270[] PROGMEM = {
#if (ENABLE_ACTUATOR_XH540 || ENABLE_ACTUATOR_XD540)
  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -1188, 1188, 2.69},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -1188, 1188, 2.69},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -1023, 1023, 0.229},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};


/* PRO R series */
const ModelDependencyFuncItemAndRangeInfo_t dependency_pro_r_m42_10[] PROGMEM = {
#if (ENABLE_ACTUATOR_PRO_R)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483647, 2147483647, 0.00136785},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483647 , 2147483647, 0.00136785},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -8000, 8000, 0.00389076},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -8000, 8000, 0.00389076},

  {SET_CURRENT, GOAL_TORQUE, UNIT_MILLI_AMPERE, -900, 900, 4.02832},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -900, 900, 4.02832},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_pro_r_m54_40[] PROGMEM = {
#if (ENABLE_ACTUATOR_PRO_R)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483647, 2147483647, 0.00143188},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483647 , 2147483647, 0.00143188},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -8000, 8000, 0.00397746},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -8000, 8000, 0.00397746},  

  {SET_CURRENT, GOAL_TORQUE, UNIT_MILLI_AMPERE, -360, 360, 16.11328},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -360, 360, 16.11328},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_pro_r_m54_60[] PROGMEM = {
#if (ENABLE_ACTUATOR_PRO_R)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483647, 2147483647, 0.00143188},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483647 , 2147483647,  0.00143188},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -8000, 8000, 0.00397746},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -8000, 8000, 0.00397746},  

  {SET_CURRENT, GOAL_TORQUE, UNIT_MILLI_AMPERE, -540, 540, 16.11328},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -540, 540, 16.11328},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_pro_r_h42_20[] PROGMEM = {
#if (ENABLE_ACTUATOR_PRO_R)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483647, 2147483647, 0.00118518},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483647 , 2147483647, 0.00118518},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -10300, 10300, 0.00329218},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -10300, 10300, 0.00329218},  

  {SET_CURRENT, GOAL_TORQUE, UNIT_MILLI_AMPERE, -1395, 1395, 4.02832},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -1395, 1395, 4.02832},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_pro_r_h54_100[] PROGMEM = {
#if (ENABLE_ACTUATOR_PRO_R)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483647, 2147483647, 0.00071724},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483647 , 2147483647, 0.00071724},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -17000, 17000, 0.00199234},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -17000, 17000, 0.00199234},  

  {SET_CURRENT, GOAL_TORQUE, UNIT_MILLI_AMPERE, -930, 930, 16.11328},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -930, 930, 16.11328},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_pro_r_h54_200[] PROGMEM = {
#if (ENABLE_ACTUATOR_PRO_R)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483647, 2147483647, 0.00071724},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483647 , 2147483647, 0.00071724},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -17000, 17000, 0.00199234},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -17000, 17000, 0.00199234},  

  {SET_CURRENT, GOAL_TORQUE, UNIT_MILLI_AMPERE, -1860, 1860, 16.11328},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -1860, 1860, 16.11328},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};


/* PRO RA, PRO PLUS series */
const ModelDependencyFuncItemAndRangeInfo_t dependency_ctable_pro_ra_pro_plus_model[] PROGMEM = {
#if (ENABLE_ACTUATOR_PRO_RA \
 || ENABLE_ACTUATOR_PRO_PLUS)
  {SET_PWM, GOAL_PWM, UNIT_RAW, -2009, 2009, 1},
  {GET_PWM, PRESENT_PWM, UNIT_RAW, -2009, 2009, 1},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_pro_ra_plus_m42_10[] PROGMEM = {
#if (ENABLE_ACTUATOR_PRO_RA \
 || ENABLE_ACTUATOR_PRO_PLUS)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483647, 2147483647, 0.00068392},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483647 , 2147483647, 0.00068392},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -2600, 2600, 0.01},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -2600, 2600, 0.01},  

  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -1461, 1461, 1.0},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -1461, 1461, 1.0},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_pro_ra_plus_m54_40[] PROGMEM = {
#if (ENABLE_ACTUATOR_PRO_RA \
 || ENABLE_ACTUATOR_PRO_PLUS)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483647, 2147483647, 0.00071594},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483647 , 2147483647, 0.00071594},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -2840, 2840, 0.01},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -2840, 2840, 0.01},  

  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -4470, 4470, 1.0},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -4470, 4470, 1.0},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_pro_ra_plus_m54_60[] PROGMEM = {
#if (ENABLE_ACTUATOR_PRO_RA \
 || ENABLE_ACTUATOR_PRO_PLUS)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483647, 2147483647, 0.00071594},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483647 , 2147483647, 0.00071594},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -2830, 2830, 0.01},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -2830, 2830, 0.01},  

  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -7980, 7980, 1.0},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -7980, 7980, 1.0},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_pro_ra_plus_h42_20[] PROGMEM = {
#if (ENABLE_ACTUATOR_PRO_RA \
 || ENABLE_ACTUATOR_PRO_PLUS)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483647, 2147483647, 0.00059259},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483647 , 2147483647, 0.00059259},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -2920, 2920, 0.01},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -2920, 2920, 0.01},  

  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -4500, 4500, 1.0},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -4500, 4500, 1.0},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_pro_ra_plus_h54_100[] PROGMEM = {
#if (ENABLE_ACTUATOR_PRO_RA \
 || ENABLE_ACTUATOR_PRO_PLUS)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483647, 2147483647, 0.00035862},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483647 , 2147483647, 0.00035862},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -2920, 2920, 0.01},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -2920, 2920, 0.01},  

  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -15900, 15900, 1.0},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -15900, 15900, 1.0},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_pro_ra_plus_h54_200[] PROGMEM = {
#if (ENABLE_ACTUATOR_PRO_RA \
 || ENABLE_ACTUATOR_PRO_PLUS)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483647, 2147483647, 0.00035862},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483647 , 2147483647, 0.00035862},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -2900, 2900, 0.01},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -2900, 2900, 0.01},  

  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -22740, 22740, 1.0},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -22740, 22740, 1.0},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_ym070_210_000_rh[] PROGMEM = {
#if (ENABLE_ACTUATOR_Y)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483648, 2147483647, 0.0006866455},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483648 , 2147483647, 0.0006866455},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -642200, 642200, 0.01},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -642200, 642200, 0.01},  

  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -2080, 2080, 0.01},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -2080, 2080, 0.01},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_ym070_210_051_rh[] PROGMEM = {
#if (ENABLE_ACTUATOR_Y)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483648, 2147483647, 0.0006866455},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483648 , 2147483647, 0.0006866455},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -12592, 12592, 0.01},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -12592, 12592, 0.01},  

  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -2080, 2080, 0.01},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -2080, 2080, 0.01},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_ym070_210_099_rh[] PROGMEM = {
#if (ENABLE_ACTUATOR_Y)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483648, 2147483647, 0.0006866455},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483648 , 2147483647, 0.0006866455},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -6486, 6486, 0.01},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -6486, 6486, 0.01},  

  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -2080, 2080, 0.01},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -2080, 2080, 0.01},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_ym080_230_000_rh[] PROGMEM = {
#if (ENABLE_ACTUATOR_Y)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483648, 2147483647, 0.0006866455},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483648 , 2147483647, 0.0006866455},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -355600, 355600, 0.01},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -355600, 355600, 0.01},  

  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -2240, 2240, 0.01},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -2240, 2240, 0.01},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_ym080_230_051_rh[] PROGMEM = {
#if (ENABLE_ACTUATOR_Y)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483648, 2147483647, 0.0006866455},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483648 , 2147483647, 0.0006866455},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -6972, 6972, 0.01},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -6972, 6972, 0.01},  

  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -2240, 2240, 0.01},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -2240, 2240, 0.01},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

const ModelDependencyFuncItemAndRangeInfo_t dependency_ym080_230_099_rh[] PROGMEM = {
#if (ENABLE_ACTUATOR_Y)
  {SET_POSITION, GOAL_POSITION, UNIT_DEGREE, -2147483648, 2147483647, 0.0006866455},
  {GET_POSITION, PRESENT_POSITION, UNIT_DEGREE, -2147483648 , 2147483647, 0.0006866455},

  {SET_VELOCITY, GOAL_VELOCITY, UNIT_RPM, -3591, 3591, 0.01},
  {GET_VELOCITY, PRESENT_VELOCITY, UNIT_RPM, -3591, 3591, 0.01},

  {SET_CURRENT, GOAL_CURRENT, UNIT_MILLI_AMPERE, -2240, 2240, 0.01},
  {GET_CURRENT, PRESENT_CURRENT, UNIT_MILLI_AMPERE, -2240, 2240, 0.01},
#endif
  {LAST_DUMMY_FUNC, ControlTableItem::LAST_DUMMY_ITEM, UNIT_RAW, 0, 0, 0}
};

static ItemAndRangeInfo_t getModelDependencyFuncInfo(uint16_t model_num, uint8_t func_num)
{
  const ModelDependencyFuncItemAndRangeInfo_t *p_common_ctable = nullptr;
  const ModelDependencyFuncItemAndRangeInfo_t *p_dep_ctable = nullptr;
  uint8_t func_idx, i = 0;
  ItemAndRangeInfo_t item_info;
  
  memset(&item_info, 0, sizeof(item_info));
  item_info.item_idx = ControlTableItem::LAST_DUMMY_ITEM;

  switch(model_num)
  {
    case AX12A:
    case AX12W:
    case AX18A:
    case DX113:
    case DX116:
    case DX117:
    case RX10:
    case RX24F:
    case RX28:
    case RX64:
      p_common_ctable = dependency_ctable_1_0_common;
      break;

    case EX106:
      p_common_ctable = dependency_ctable_1_0_common;
      p_dep_ctable = dependency_ex;
      break;

    case MX12W:
      p_common_ctable = dependency_ctable_1_1_common;
      p_dep_ctable = dependency_mx12;
      break;

    case MX28:
      p_common_ctable = dependency_ctable_1_1_common;
      break;

    case MX64:
    case MX106:
      p_common_ctable = dependency_ctable_1_1_common;
      p_dep_ctable = dependency_mx64_mx106;
      break;              

    case XL320:
      p_common_ctable = dependency_xl320;
      break;

    case MX28_2:
    case XC430_W150:
    case XC430_W240:
    case XXC430_W250:
    case XL430_W250:
    case XXL430_W250:
      p_common_ctable = dependency_ctable_2_0_common;
      p_dep_ctable = dependency_xl430_xc430;
      break;

    case MX64_2:
      p_common_ctable = dependency_ctable_2_0_common;
      p_dep_ctable = dependency_mx64_2;
      break;    

    case MX106_2:
      p_common_ctable = dependency_ctable_2_0_common;
      p_dep_ctable = dependency_mx106_2;
      break;     

    case XL330_M288:
    case XL330_M077:
      p_common_ctable = dependency_ctable_2_0_common;
      p_dep_ctable = dependency_xl330_M288_M077;
      break;

    case XC330_M181:
    case XC330_M288:
      p_common_ctable = dependency_ctable_2_0_common;
      p_dep_ctable = dependency_xc330_m181_m288;
      break;

    case XC330_T181:
    case XC330_T288:
      p_common_ctable = dependency_ctable_2_0_common;
      p_dep_ctable = dependency_xc330_t181_t288;
      break;

    case XM335_T323:
      p_common_ctable = dependency_ctable_2_0_common;
      p_dep_ctable = dependency_xm335_t323;
      break;

    case XM430_W210:
    case XM430_W350:
      p_common_ctable = dependency_ctable_2_0_common;
      p_dep_ctable = dependency_xm430_w210_w350;
      break;

    case XH430_V210:
    case XH430_V350:
      p_common_ctable = dependency_ctable_2_0_common;
      p_dep_ctable = dependency_xh430_v210_v350;
      break;

    case XH430_W210:
    case XH430_W350:
    case XD430_T210:
    case XD430_T350:
      p_common_ctable = dependency_ctable_2_0_common;
      p_dep_ctable = dependency_xh430_wt210_wt350;
      break;    

    case XW430_T200:
    case XW430_T333:
      p_common_ctable = dependency_ctable_2_0_common;
      p_dep_ctable = dependency_xw430_t200_t333;
      break;   

    case XM540_W150:
    case XM540_W270:
    case XH540_W150:
    case XH540_W270:    
    case XD540_T150:
    case XD540_T270:    
    case XW540_T140:
    case XW540_T260:
      p_common_ctable = dependency_ctable_2_0_common;
      p_dep_ctable = dependency_xm540_xh540_xt540_xw540;
      break;

    case XH540_V150:
    case XH540_V270:
      p_common_ctable = dependency_ctable_2_0_common;
      p_dep_ctable = dependency_xh540_v150_v270;
      break;

    // case PRO_L42_10_S300_R:
    // case PRO_L54_30_S400_R:
    // case PRO_L54_30_S500_R:
    // case PRO_L54_50_S290_R:
    // case PRO_L54_50_S500_R:
    case PRO_M42_10_S260_R:
      p_common_ctable = dependency_pro_r_m42_10;
      break;    

    case PRO_M54_40_S250_R:
      p_common_ctable = dependency_pro_r_m54_40;
      break;  

    case PRO_M54_60_S250_R:
      p_common_ctable = dependency_pro_r_m54_60;
      break;  

    case PRO_H42_20_S300_R:
      p_common_ctable = dependency_pro_r_h42_20;
      break;   

    case PRO_H54_100_S500_R:
      p_common_ctable = dependency_pro_r_h54_100;
      break;    

    case PRO_H54_200_S500_R:
      p_common_ctable = dependency_pro_r_h54_200;
      break;
    
    case PRO_M42_10_S260_RA:    
    case PRO_M42P_010_S260_R:
      p_common_ctable = dependency_ctable_pro_ra_pro_plus_model;
      p_dep_ctable = dependency_pro_ra_plus_m42_10;
      break;

    case PRO_M54_40_S250_RA:
    case PRO_M54P_040_S250_R:
      p_common_ctable = dependency_ctable_pro_ra_pro_plus_model;
      p_dep_ctable = dependency_pro_ra_plus_m54_40;
      break;

    case PRO_M54_60_S250_RA:
    case PRO_M54P_060_S250_R:
      p_common_ctable = dependency_ctable_pro_ra_pro_plus_model;
      p_dep_ctable = dependency_pro_ra_plus_m54_60;
      break;

    case PRO_H42_20_S300_RA:
    case PRO_H42P_020_S300_R:
      p_common_ctable = dependency_ctable_pro_ra_pro_plus_model;
      p_dep_ctable = dependency_pro_ra_plus_h42_20;
      break;

    case PRO_H54_100_S500_RA:  
    case PRO_H54P_100_S500_R:
      p_common_ctable = dependency_ctable_pro_ra_pro_plus_model;
      p_dep_ctable = dependency_pro_ra_plus_h54_100;
      break;

    case PRO_H54_200_S500_RA:
    case PRO_H54P_200_S500_R:
      p_common_ctable = dependency_ctable_pro_ra_pro_plus_model;
      p_dep_ctable = dependency_pro_ra_plus_h54_200;
      break;

    case YM070_210_M001_RH:
    case YM070_210_B001_RH:
      p_common_ctable = dependency_ym070_210_000_rh;
      break;
    case YM070_210_R051_RH:
    case YM070_210_A051_RH:
      p_common_ctable = dependency_ym070_210_051_rh;
      break;
    case YM070_210_R099_RH:
    case YM070_210_A099_RH:
      p_common_ctable = dependency_ym070_210_099_rh;
      break;
    case YM080_230_M001_RH:
    case YM080_230_B001_RH:
      p_common_ctable = dependency_ym080_230_000_rh;
      break;
    case YM080_230_R051_RH:
    case YM080_230_A051_RH:
      p_common_ctable = dependency_ym080_230_051_rh;
      break;
    case YM080_230_R099_RH:
    case YM080_230_A099_RH:
      p_common_ctable = dependency_ym080_230_099_rh;
      break;

    default:
      break;
  }

  if(p_common_ctable == nullptr){
    return item_info;
  }

  do{
    func_idx = pgm_read_byte(&p_common_ctable[i].func_idx);
    if(func_idx == func_num) {
      item_info.item_idx = pgm_read_byte(&p_common_ctable[i].item_idx);
      item_info.min_value = (int32_t)pgm_read_dword(&p_common_ctable[i].min_value);
      item_info.max_value = (int32_t)pgm_read_dword(&p_common_ctable[i].max_value);
      item_info.unit_type = pgm_read_byte(&p_common_ctable[i].unit_type);
      item_info.unit_value = pgm_read_float(&p_common_ctable[i].unit_value);
      break;
    }
    i++;
  }while(func_idx != LAST_DUMMY_FUNC);

  if(p_dep_ctable == nullptr) {
    return item_info;
  }

  i = 0;
  do{
    func_idx = pgm_read_byte(&p_dep_ctable[i].func_idx);
    if(func_idx == func_num) {
      item_info.item_idx = pgm_read_byte(&p_dep_ctable[i].item_idx);
      item_info.min_value = (int32_t)pgm_read_dword(&p_dep_ctable[i].min_value);
      item_info.max_value = (int32_t)pgm_read_dword(&p_dep_ctable[i].max_value);
      item_info.unit_type = pgm_read_byte(&p_dep_ctable[i].unit_type);
      item_info.unit_value = pgm_read_float(&p_dep_ctable[i].unit_value);
      break;
    }
    i++;
  }while(func_idx != LAST_DUMMY_FUNC);

  return item_info;  
}

static bool checkAndconvertWriteData(float in_data, int32_t &out_data, uint8_t unit, ItemAndRangeInfo_t &item_info)
{
  float data_f = 0.0;
  int32_t data = 0;  

  switch(unit)
  {
  case UNIT_RAW:
    data = (int32_t)in_data;
    if(data < item_info.min_value || data > item_info.max_value)
      return false;
    break;

  case UNIT_PERCENT:
    data_f = f_map(in_data, -100.0, 100.0,
     (float)item_info.min_value, (float)item_info.max_value);
    data = (int32_t)data_f;
    break;

  case UNIT_RPM:
  case UNIT_DEGREE:
  case UNIT_MILLI_AMPERE:
    if(unit != item_info.unit_type)
      return false;
    data = (int32_t)round(in_data/item_info.unit_value);

    if(data < item_info.min_value || data > item_info.max_value)
      return false;
    break;

  default:
    return false;
  }

  out_data = data;

  return true;
}

static bool checkAndconvertReadData(int32_t in_data, float &out_data, uint8_t unit, ItemAndRangeInfo_t &item_info)
{
  float data = 0;  

  switch(unit)
  {
  case UNIT_RAW:
    data = (float)in_data;
    break;

  case UNIT_PERCENT:
    data = (float)f_map(in_data, 
     (float)item_info.min_value, (float)item_info.max_value, -100.0, 100.0);
    break;    

  case UNIT_RPM:
  case UNIT_DEGREE:
  case UNIT_MILLI_AMPERE:
    if(unit != item_info.unit_type)
      return false;

    data = (float)in_data*item_info.unit_value;
    break;

  default:
    return false;
  }

  out_data = data;

  return true;
}

static float f_map(float x, float in_min, float in_max, float out_min, float out_max)
{
  return (x - in_min) * (out_max - out_min) / (in_max - in_min) + out_min;
}